Electrolux FAC124P1A Instruções de Operação descarregar pdf (Página 50)

Section 2 Installation

2-20

8,000-12,000 BTU Thru-The-Wall

Installation Instructions

For Existing Sleeve

Note that the air conditioner dimensions are: 24” wide,

14-1/2” high, and 18-1/2” deep (without front). Install air

conditioner according to these installation instructions

to achieve the best performance.

Items in the Thru-The-Wall Kit

You may not need all parts in the kit. Discard unused

parts.

Part Description Qty.

Tapered Spacer Blocks ..................... 17” Long ........ 2

Centering/Support Blocks ...4-½”x 3-½”x 1-½” ......... 2

Plastic Divider ...................⅛” x 4-½”x 14-½” ........ 1

Stuffer Seal .............................1”x 1-½ “x 84” ........ 1

Seal ...............................1-½”x 1-½”x 26-½” ........ 2

Seal ................................... 1-½”x 1-½”x 14” ........ 2

Seal ..................................1-½”x ⅜”x 26-½” ........ 2

Seal ...................................... 1-½”x ⅜”x 14” ........ 2

Seal ..........................................1” x ¾”x 14” ........ 1

Trim Frame (side legs) ............................................. 2

Trim Frame (top & bottom legs) ............................... 2

Ground Wire (green) ............................................... 1

Nut for grounding screw .......................................... 1

Grounding Screw ..................................................... 1

Grille (plastic) ......................................................... 1

Nuts (plastic) .......................................................... 4

Screw w/washer ...................................................... 4

How to Install

Wall Sleeve Dimensions

Width Height Depth

25-1/2” 15-1/4” 16”, 17-1/2” or 22”

2. Remove old Air Conditioner from wall sleeve and

prepare wall sleeve as follows:

a. Clean interior (do not disturb seals).

b. Wall sleeve must be securely fastened in wall

before installing Air Conditioner. Drive more nails

or screws through sleeve into wall if needed.

c. Repair paint if needed.

3. If not existing, drill a 3/16” clearance hole for

grounding screw through left side of wall sleeve in

a clear area about 3 inches maximum (to suit) back

from front edge of sleeve as shown in Figure 2-61.

Next attach ground wire inside sleeve, using

grounding screw and nut. Pull loose end of ground

wire out front of sleeve and temporarily bend it

down and around lower edge of sleeve.

4. Prepare the wall sleeve for installation of the new

unit per the following instructions.

Frigidaire 16”+ 17-1⁄2” Deep

Frigidaire 22” Deep

Install new unit into wall sleeve.

6. To attach ground wire to the new unit, remove the

screw from the left side front.

7. Assemble and install the Trim Frame.

Rear

Unit

Front

Level

1/4” to 5/16”

Sleeve

Wall

Wall Sleeve To Unit

Sleeve Grounding

Max.

Hole

Figure 2-60.

All wall sleeves used to mount a new Air Conditioner

must be in sound structural condition and have a rear

grille that securely attaches to sleeve, or rear flange

that serves as a stop for the Air Conditioner.

NOTE

When installation is complete, replacement unit MUST

have a rearward slope as shown in Figure 2-60.

CAUTION

Figure 2-61.

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 139 140

Comentários a estes Manuais

Sem comentários

Electrolux FAC124P1A Instruções de Operação Página 50

Comentários a estes Manuais

Manuais e produtos relacionados com Aparelhos de ar condicionado "split system" Electrolux FAC124P1A