Electrolux 61371 M and Manual do Operador

A-61371 April 2010 1-3Grounding To prevent electrical shocks caused by electrical leakage, always ground the printer. • Connect the grounding wire t

1-4 A-61371 April 2010Operating environmentThe environmental requirements for operating the system are as follows:Temperature: 10° to 35°C (50 to 95

A-61371 April 2010 1-5Scanner components Front view1 Screen — the image from the film is displayed for viewing on the screen. The frame on the scree

1-6 A-61371 April 2010Rear view9 Power Switch — used to turn the power to the unit on and off.10 Connectors — provides connection points for the var

A-61371 April 2010 1-7Optional accessories Optional accessories are available for the scanner. Contact your Kodak Representative for more informatio

1-8 A-61371 April 2010Film carriers Fiche Carrier-5 — for use with jackets, microfiche and aperture cards.UC-2 — a motorized carrier for semi-automa

A-61371 April 2010 1-9Turning the power on and offTo turn the power on:• Press the power switch of the scanner to the (I) On position.• Press the po

1-10 A-61371 April 2010To turn the power off• Press the power switch of the scanner to the O (Off) position. • Press the power switch of the printer

A-61371 April 2010 2-12 Control Panel and FunctionsFollowing are descriptions of the Control Panel functions. Some functions are available by using

2-2 A-61371 April 2010 2 Lamp Illuminance — manually adjusts the Projection Lamp illuminance. When the Projection Lamp is Off, it can be turned On a

A-61371 April 2010 iSafetyThe following information contains important information related to operator safety and may help prevent equipment problem

A-61371 April 2010 2-310 Exposure Adjustment — adjusts the density of the image to be printed during the Auto or Manual Exposure mode.• Darker: supp

2-4 A-61371 April 2010 Using the Shift function on Control Panel 1When you use the Shift function (Clear/Stop key) on Control Panel 1, other options

A-61371 April 2010 2-5Control Panel 2 1 Centering/Fit key — when pressed, enables or disables the Centering and Fit functions. When Auto Masking, Tr

2-6 A-61371 April 2010 3 Auto Masking — turns auto masking on or off. Auto masking omits the frame (non-image area) of a printed film image. Auto ma

A-61371 April 2010 2-7Image processing featuresThis section provides a description of the image processing features. Procedures on how to use these

2-8 A-61371 April 2010 Screen Image to Print ImageDescriptionPage-by-Page PrintThe system takes two film images that appear side-by-side on the scre

A-61371 April 2010 3-13 Using the ScannerThis chapter provides procedures on how to us the Kodak 3000 DV Plus Digital Scanner.Following is an outlin

3-2 A-61371 April 2010 Selecting a projection lensProjection lenses are available in the following types. Select the type of lens that corresponds t

A-61371 April 2010 3-3Replacing the projection lensTo replace a lens with a magnification different from the pre-installed lens.1. Grasp the Prism H

3-4 A-61371 April 2010 Positioning the film imageThe size frame markers that correspond to the scanning size are marked on the screen. Through zoomi

ii A-61371 April 2010• Do not use this product in an area where ammonia or other gases or chemicals are present. • Do not use this product in an env

A-61371 April 2010 3-5Zooming, focusing and image rotationZooming in on the displayed image:• Turn the Zooming Ring dial (blue) to bring the image o

3-6 A-61371 April 2010 Selecting the film typeAutoThe system will automatically determine the polarity of the film being used when Auto is selected.

A-61371 April 2010 3-7Selecting the paper sizePress the Paper Selection key to select the desired print size. The system cycles through the availabl

3-8 A-61371 April 2010 Using the Auto Film Format Selection functionWhen the paper feeding tray and paper cassette is loaded with8 1/2 x 11” (A4) pa

A-61371 April 2010 3-9Selecting the image densityUsing Auto Exposure1. Press the Exposure Mode key to select the Auto Exposure mode.2. If the Auto E

3-10 A-61371 April 2010 Entering the number of prints to be madeThis function is only available in PR mode.Entering a number from 1-9• Enter the des

A-61371 April 2010 3-11Adjusting Image Processing featuresUsing Auto Masking The Auto Masking function prevents the frame (non-image area) of a film

3-12 A-61371 April 2010 Manual Masking panels (option)1 Lengthwise Area Indication panel — use to specify the print area in the vertical direction o

A-61371 April 2010 3-13Selecting Trimming• Press the Masking key to select Trimming. The lights on the panel light up according to the currently sel

3-14 A-61371 April 2010 Defining two separate areas• Define the areas to print by specifying the vertical and horizontal areas as follows: 2 end poi

A-61371 April 2010 iiiREACH statementPlease consult www.kodak.com/go/REACH for information about the presence of substances included on the candidat

A-61371 April 2010 3-15Clearing a defined print area• Press the Vertical and Horizontal Clear keys. Selecting Masking• Press the Masking key to se

3-16 A-61371 April 2010 Centering• Press the Centering/Fit key to turn on Centering.NOTE: Centering/Fit mode cannot be used if Masking is selected.F

A-61371 April 2010 3-17Specifying the interval between scanning operationsThe chart below provides the time intervals that can be set between scanni

3-18 A-61371 April 2010 Selecting the Resolution 1. Press the Shift key and the Resolution key together. The current resolution is displayed.2. Pres

A-61371 April 2010 3-19Calling the Job Program To call a registered Job Program:1. Press the Shift key and the Job Recall key together.Each time the

3-20 A-61371 April 2010 Skip magnificationHold down the 10 key and the Zoom+ or Zoom- key together, the magnification skips as follows:Clearing the

A-61371 April 2010 4-14 Printer FunctionsThis chapter provides information on how to use and maintain your Kodak 34 ppm High Speed Video Laser Printe

4-2 A-61371 April 2010 8 Interface connectors ⎯ these two connectors allow the connection with separate scanner units.9 Power cord socket ⎯ plug the

A-61371 April 2010 4-3Paper specifications Use only the following types of paper:Type — plain and recycled paper (weight 16 to 24 lbs / 60 to 90 g/m2

4-4 A-61371 April 2010 4. While pressing the button on the right side of the media guide, slide the media guide to adjust it.NOTE: Make sure the pap

iv A-61371 April 2010All other usersWARNING: Use of controls, adjustments of performance or procedures other than those specified in this manual may

A-61371 April 2010 4-54. Lift up the gray lever on the right end of the paper retainer, and slide the paper retainer to the right.5. Lift up on the l

4-6 A-61371 April 2010 8. Align the four edges of the paper, and then load the paper printing side up.NOTE: A maximum of 500 sheets (20 lb. bond [75

A-61371 April 2010 4-712.When printing on paper B4 or larger, fold open the output tray extension.13.Affix the paper size labels (supplied with the p

4-8 A-61371 April 2010 Replacing the toner cartridge1. Slide the top cover release lever to the right, and open the top cover NOTES:• Never touch th

A-61371 April 2010 4-94. Peel off the packing tape.NOTE: Hold the toner cartridge by its handle. Do not open the protective cover of the OPC (the gre

4-10 A-61371 April 2010 6. Align the tabs on the cartridge (one on each side) with the notches in the printer, and then insert the cartridge as far

A-61371 April 2010 4-11Replacing the exhaust filterReplace the exhaust filter on the back of the printer when you replace the toner cartridge.1. Remo

4-12 A-61371 April 2010 Clearing a misfeed from the paper feeding tray1. Remove all paper from the paper feeding tray.2. Pull out the misfed paper.3

A-61371 April 2010 4-134. After removing the misfed paper, lower the two levers.5. Open the paper feed roller cover.6. Pull out the jammed paper.7. C

4-14 A-61371 April 2010 Printer maintenance Clean the printer at regular intervals.NOTES:• Use a soft cloth and NEVER use abrasives or corrosive det

A-61371 April 2010 iContents1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1Product descriptio

A-61371 April 2010 5-15 MaintenanceThis chapter provides maintenance procedures for cleaning the scanner and replacing the projection lamp.Cleaning

5-2 A-61371 April 2010 Carrier Glass (option)NOTE: Before cleaning the carrier glass, remove the projection lens from the scanner. Refer to Chapter

A-61371 April 2010 5-3Replacing the projection lampUse the following procedure to replace the projection lamp whenever a reduction in brightness on

5-4 A-61371 April 2010 5. Insert the new projection lamp so that the mark on its base is facing upwards. Make sure that the new projection lamp is i

A-61371 April 2010 6-16 Troubleshooting/MessagesThis chapter contains information on analyzing and correcting operating problems or errors that may

6-2 A-61371 April 2010 Solving printing problemsUse the following procedures to fix minor printing problems. If print quality does not improve after

A-61371 April 2010 A-1Appendix A SpecificationsThe following are specifications for the Kodak 3000 DV Plus Digital Scanner and the Kodak 34 ppm Vide

A-2 A-61371 April 2010 PR Mode - Kodak 34 ppm Video Laser PrinterSpecificationsResolution 600 dpiOutput Scale BinaryPrinting Method Laser Electrosta

A-61371 April 2010 B-1Appendix B User and System SettingsThis system offers these settings:• User settings that are set up by the user from the cont

B-2 A-61371 April 2010 System Setting Selection Initial SettingDescriptionFine mode contrast select Contrast EmphasisOutline Emphasis* Applies the f

ii A-61371 April 2010 4 Printer Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Printer components . . .

A-61371 April 2010 B-3* To change any of the system settings described above, contact your Kodak Service Representative.System Setting Selection Ini

A-61371 April 2010 C-1Appendix C Key Operator InformationWhen you need to call for service, be prepared to provide the following information:• Your

A-61371 April 2010 D-1Appendix D Setting System Default ValuesChanging settings with the User modeUser mode allows the default values of various fun

D-2 A-61371 April 2010 Entering and exiting the User mode1. Hold down the Shift key and Paper Selection key at the same time for 0.5 seconds. The Mu

A-61371 April 2010 D-3Settings in each User mode functionU1: Special Print mode — this function is not available.U2: Engineering Enhancement mode —

D-4 A-61371 April 2010 U4: Paper Feeding Tray Size — the size an direction of the paper loaded in the Paper Feeding Tray can be set with this functi

A-61371 April 2010 D-5U6: Year, Month and Date Set mode —the print pattern for the Date Print function can be set with this function.1. Select U6 in

D-6 A-61371 April 2010 3. In each setting mode, press the Multi-Print key to enter the setting value. Each press of the Multi-Press key increases th

A-61371 April 2010 1-11 OverviewThis Operator’s Manual provides information and procedures for using the Kodak 3000 DV Plus Digital Scanner. Followi

1-2 A-61371 April 2010Installation Placement of the unit in the environment described below will ensure optimal performance throughout the long life