Electrolux 2005-04 Manual do Operador descarregar pdf (Página 15)

Before performing any maintenance, ALWAYS

place the machine on a level surface with the

motor OFF and disconnect the electrical

current. Let the machine cool down!!

Your TARGET® tile saw is a ruggedly constructed

machine, engineered to give long, satisfactory

performance. Simple daily maintenance and care will add

to the life and productivity of your saw. After each day’s

use: CLEAN THE MACHINE!!

* Turn off and unplug the saw before performing

any maintenance.

* Keep the cart top clean and free for cuttings.

To clean it, flush the top surface and grooves

with water.

* Drain, clean and refill the pan frequently. Flush

the coolant system with plenty of water, then

drain and refill the pan.

* If the water flow stops, check the water pump to

see if the shaft and impeller turn freely. See the

been installed. (Refer to Section 5, Adjustable

Lockbar, if needed)

• Install the profile wheel onto the spindle shaft up

against the inner flange with the working surface to

the outside.

• Secure into place by reversing the outer flange and

tightening the spindle nut. Lower the Blade Guard

(J) back down over the profile wheel.

• Locate the material for profiling:

1. Set the edge of the part to be shaped parallel to

the wheel.

2. Locate the material under the wheel. Pull the

Conveyor Cart (4) with the material from under

the wheel to set proper cutting height.

3. Loosen the Locking Knob (C) and lower the

Cutting Head (1) so that the wheel just slightly

makes contact with the material.

4. Secure the Cutting Head (1) into position with

the Locking Knob (C) for cutting.

5. Note: Profiling usually takes several light passes

to produce the best results. Set lower each time

until the desire depth has been reached.

If Water Stops Flowing,

1. Stop Sawing, then

2. Disconnect Electrical Plug from Outlet, then

3. Remove the Pump, then

4. Back Flush.

Back flushing is done by forcing water into the pump

discharge and out through the screen. Most of the time

this procedure works, and the pump can be put back into

service. (See Figure below)

If the back flushing does not work, remove the screen and

turn the impeller manually, looking for and rinsing out the

impeller cavity of any dirt or foreign matter.

FIGURE 4

11 MAINTENANCE PROCEDURES

12 WATER PUMP TROUBLE-SHOOTING PROCEDURE

10 PLUNGE CUTTING

See Figure 2

Spring Force can be adjusted by rotating Spring Anchor

(24). Loosen .375-16 NC Bolt (29) and rotate Spring

Anchor (24) to increase or decrease Spring Force. Tighten

Bolt to secure Anchor to Pivot Shaft. It may be necessary

to slightly loosen the Bearing Caps for proper and smooth

operation. By loosening Knob (26), Pivot Head can be

raised or lowered with minimal effort, depending on Spring

Force adjustment. A second Spring Anchor (24) is located

on the underside of the Platform and is used as a set collar

and as a stop for the Platform.

WATER PUMP TROUBLE-SHOOTING

PROCEDURE section.

* It is always good practice to clean your tile saw

after each day’s use. Drain the water and clean

out the pan. Clean the rails. Before storing, it

is good practice to wipe or spray rails with water-

soluble oil (like, WD-40 or equivalent).

Entrust all repairs to your authorized dealer

only.

For quick supply of spare parts and to avoid any lost time,

it is essential to quote the data on the manufacturers plate

fixed to the machine and the part number(s) and description

to be replaced with every order.

We carry out all repairs in the shortest possible time and at

the most economical prices. (See front page for

address and phone numbers) Contact your authorized

TARGET® dealer concerning maintenance and repairs.

13 REPAIRS

14 SPARE PARTS

1 2 ... 10 11 12 13 14 15 16 17 18 19 20

Comentários a estes Manuais

Sem comentários

Electrolux 2005-04 Manual do Operador Página 15

Comentários a estes Manuais

Manuais e produtos relacionados com Corta-relvas Electrolux 2005-04