Electrolux C67600K Manual do Utilizador

C67600KCeramic glass induction hobInstallation and Operating Instructions

50Description of the ApplianceCooking zones and control panel Radiated heat cooking zone 1200 WInduction cooking zone 2200 Wwith power function 3000 W

51Function and the Way the Induction Cooking Zone WorksA copper wire induction coil is beneath the ceramic glass cooking sur-face. This generates elec

52The following letters and functions are displayed only with the two in-duction cooking zones.1 f = Error displayflashes if the cooking zone is activ

53Suitable Kitchenware for Induction Cooking ZonesPots and Pans• In principle all pots and pans with magnetic bases are suitable. These are steel, ste

54Note:Please note the diameter of the pan base when buying new pans, since the manufacturers usually specify the top edge diameter of their pans.Auto

55Before Using for the First TimemeInitial CleaningWipe the ceramic glass surface with a damp cloth.1 Important: Do not use any caustic, abrasive clea

56Operating the HobTouch Control Sensor FieldTo operate the Touch Control sensor field place your finger from above flat onto the required field until

573 When an individual cooking zone or the entire hob is switched off, any residual heat is shown with an h (for “Hot”) in the digital display for the

583 If several cooking zones are being used simultaneously, the required cooking zone must be selected by touching the appropriate sensor field before

59Switching the Casserole Zone On and Off1. Select the appropriate cooking zone. 2. Set the required heat setting. 3. To switch the casserole zone on

42Dear customer,Please read these operating instructions carefully.Pay particular attention to the section “Safety information” on the first few pages

60Switching off a Cooking Zone1. Select the required cooking zone with the cooking zone sensor fields.2. Touch sensor fields + and - simultaneously to

61Cooking with the Automatic Heating-Up FunctionAll four cooking zones of the cooking field can be controlled in nine stages and have an automatic hea

62a lights up in the heat setting display. 3. Next, touch the sensor field - and set the required continued heat set-ting 1 to 8. The heat setting sel

63Cooking without the Automatic Heating-Up Function1. For heating up/browning, select a high power.2. As soon as steam forms or the fat is hot, switch

64Locking/Unlocking the Control PanelWith the exception of the “On/Off” sensor field the control panel can be locked at any required time during cooki

65TimerA cooking duration can be set with the integrated timer for all cooking zones. When the end of the cooking duration is reached, the cooking zon

663 To set the timer more quickly, leave your finger on the + or - sensor field until the required time is reached.If the - sensor field is operated f

67Uses, Tables and TipsAdvice on Cooking with and without Automatic Warm upThe automatic warm up function is suitable for:• dishes that start off cold

68Chart for Setting the Cooking ZonesHeat setting suitable for9 or P Heating UpHeating up large quantities of water, cooking pasta7-9 Heavy BrowningDe

69Chart for the Automatic Heating-Up FeatureExample foodsCooking processesHeat setting Duration Notes/tipsSteaks Heavy browningA7 to A8 per pan 8-20 m

43ContentsOperating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Safety . . . . . . . . . . . . . . . . . .

70Cleaning and CareAdvantages for Cleaning and Caring for the Induction Cooking Zone2 The cleaning effort for induction ceramic glass cooking surfaces

71Stubborn Soiling1. To remove food that has boiled over or stubborn splashes, use a glass scraper. 2. Place the glass scraper at an angle to the cer

72What to do if …Rectifying faultsIt is possible that faults have been caused by a minor error, which you can correct yourself with the help of the fo

73… the residual heat indicator suddenly fails to operate except for _ or h. Check whether – the “On/Off” switch was activated by mistake.– the sensor

74… the power function cannot be switched on– Switch off the cooking zone for approx. 10 minutes.If this fault occurs repeatedly check whether– the re

75Installation Instructions1Important! The new appliance may only be installed and connected by qualified personnel.Please observe this instruction, o

76Regulations, Standards, DirectivesThis appliance meets the following standards:• EN 60 335-1 and EN 60 335-2-6relating to the safety of electrical a

771 Safety Instructions for the Installer• A device must be provided in the electrical installation which allows the appliance to be disconnected from

78Electrical ConnectionBefore connecting, check that the nominal voltage of the appliance, that is the voltage stated on the rating plate, corresponds

79

44What to do if … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Rectifying faults. . . . . . . . .

80

81ServiceIn the “What to do if …” section a number of malfunctions are listed that you can rectify yourself Look there first if a fault occurs. Is it

124Montage / Assembly / Montage

125

126 AusbauRemovalDémontage

From the Electrolux Group. The world´s No.1 choice.The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning an

45Operating Instructions1 SafetyThe safety aspects of this appliance comply with accepted technical standards and the German Appliance Safety Law. How

46• Overheated fats and oils catch fire quickly. You should supervise cooking when preparing foods in fat or oil (e.g. chips).• Switch off the cooking

47• Make sure that no acidic liquids, e.g. vinegar, lemon or descaling agents, are spilt onto the hob frame, since these cause dull spots.• If sugar o

482 DisposalDisposing of the packaging materialAll materials used can be fully recycled.Plastics are marked as follows:• >PE< for polyethylene,

49The Key Features of Your Appliance• Ceramic glass cooking surface: The appliance has a ceramic glass cooking surface including two rapid-heating coo